Aluminum 6061, Al 6061-T6 Alloy Properties, Density,
Aluminum 6061-T6 has a minimum yield strength of 35 ksi (240 MPa), which is almost equal to that of A36 steel. This strength, combined with its light weight
T6 Aluminium Alloy
We are more than an aluminium alloy solution provider.
Do you need consumer aluminium alloy products or learn more info about aluminum alloy prices?
Aluminum 6061-T6 Material Information Specifications -
Aluminum 6061-T6 is the one of the most common types of aluminum metals used in the industrial world today. With its high strength-to-weight ratio and excellent mability, it
Aluminum 6063-T6 T5; AA 6063 Aluminum Alloy Properties - The
Aluminum 6063-T6, T5 (AA6063 Alloy) AA 6063 aluminum is one of the Al-Mg-Si series aluminum alloys, containing about 1% Mg 2 Si. It has excellent extrudability, moderate
Aluminium Alloy - Commercial Alloy - 6005A - T6
6005A - T6 Extrusion. Aluminium alloy 6005A is a medium strength, heat treatable alloy with excellent corrosion resistance. Alloy 6005 has properties between those of alloys
Aluminium Alloy - Commercial Alloy - 6063 - T6
6063 - T6 Extrusions. Aluminium Alloy 6063 Aluminium alloy 6063 is a medium strength alloy commonly referred to as an architectural alloy. It is normally used in intricate
Aluminium Alloy
virgin and recycled aluminium alloys. Pure aluminium is soft, ductile, corrosion resistant and has a high electrical conductivity. It is widely used for T6 220
T6 Heat Treatment - an overview | ScienceDirect
The material tested was 6061 aluminum alloy (6061 Al alloy) which received T6 heat treatment. Mises’ equivalent total strain controlled nonproportional low cycle fatigue tests
Aluminum 6063-T6 T5; AA 6063 Aluminum Alloy
Aluminum 6063-T6, T5 (AA6063 Alloy) AA 6063 aluminum is one of the Al-Mg-Si series aluminum alloys, containing about 1% Mg 2 Si. It has excellent extrudability, moderate strength, good weldability, corrosion resistance and resistance to stress corrosion cracking (SCC), widely used in extruded architectural profiles and decorative
6063 aluminium alloy -
T6 temper 6063 has an ultimate tensile strength of at least 190 MPa (28,000 psi) and yield strength of at least 160 MPa (23,000 psi). In thicknesses of 3.15 millimetres (0.124 in) or less, it has elongation of 8% or more; in thicker sections, it has elongation of
Aluminum 6061-T6 Material Information Specifications -
Overview. Aluminum 6061-T6 is the one of the most common types of aluminum metals used in the industrial world today. With its high strength-to-weight ratio and excellent mability, it is perfect for applications in aerospace, transportation equipment and construction materials manufacturing. Aluminum 6061-T6 is generally heat treated and
Aluminium 6060 T5, T6, T4; Aluminum Alloy 6060
Aluminium 6060-T6 mechanical properties are listed in the table below, including tensile strength, yield strength, elongation, hardness, etc. DIN EN 755-2 6060 aluminum alloy extruded Bars and Tubes Profiles Notes: Dimensions: diameter of round bars or width across flats of square and hexagonal bars, thickness of rectangular
Aluminium Alloy - Commercial Alloy - 6063 - T6 Extrusions -
Aluminium alloy 6063 is a medium strength alloy commonly referred to as an architectural alloy. It is normally used in intricate extrusions. It has a good surface finish, high corrosion resistance, is readily suited to welding and can be easily anodised. Most commonly available as T6 temper, in the T4 condition it has good
T6 Temper - an overview | ScienceDirect
The majority of the residual stress studies have focused on 6061Al in T6 temper condition with the exception of 6013Al-T4 and 6082Al-T6 alloys. As reported for the 2XXX and 5XXX series aluminum alloys, maximum tensile stresses were longitudinal RS which ranged from 43% [27] to 99% [21] of the YS of the BM at room temperature. The highest
Aluminium Alloy
virgin and recycled aluminium alloys. Pure aluminium is soft, ductile, corrosion resistant and has a high electrical conductivity. It is widely used for T6 AA3103 H 9 29 AA H12 H14 H16 H 110-150
Aluminium–copper alloys -
Aluminium-copper alloys (AlCu) are aluminum alloys that consist largely of aluminum (Al) and traces of copper The AlCu cast alloys are prone to hot cracking and are used in the T4 and T6 hardening states. The following table shows the composition of some grades according to DIN EN 1706. All data in percent by mass, the rest is
7108 (7108-T6) Aluminum ::
Home >Aluminum Alloy>AA 7000 Series (Aluminum-Zinc Wrought Alloy) 7108 (7108-T6) Aluminum 7108 aluminum is a 7000-series aluminum alloy: the main alloying addition is zinc and it is formulated for primary forming into wrought products. Cited properties are appropriate for the T6
Standard Specification for Aluminum-Alloy 6061-T6 Standard
Scope. 1.1 This specification covers extruded 6061-T6 aluminum-alloy standard structural profiles. 1.2 The profiles are limited to I-beams, H-beams, channels, angles, tees, and zees. Note 1—For other extruded profiles in other alloys and tempers refer to Specification B221. 1.3 Alloy and temper designations are in accordance with
Aluminium Alloy
virgin and recycled aluminium alloys. Pure aluminium is soft, ductile, corrosion resistant and has a high electrical conductivity. It is widely used for T6 AA3103 H 9 29 AA H12 H14 H16 H 110-150
Aluminium Alloy - Commercial Alloy - 6063 - T6 Extrusions -
Aluminium alloy 6063 is a medium strength alloy commonly referred to as an architectural alloy. It is normally used in intricate extrusions. It has a good surface finish, high corrosion resistance, is readily suited to welding and can be easily anodised. Most commonly available as T6 temper, in the T4 condition it has good
ASM Material Data Sheet -
Key Words: Aluminium 2024-T6; UNS A92024; ISO AlCu4Mg1; AA2024-T6 Material Notes: Weldability = C; Stress Corrosion Cracking Resistance = B; General Corrosion Resistance = D (A = best; E = worst). Good mability and surface finish capabilities. A high strength material of adequate
6061-T6 Aluminum Properties - Norsk
6061-T6 aluminum properties include its structural strength and toughness. It is also offers good finishing characteristics and responds well to anodizing, including clear, clear and color dye, and hardcoat. 6061 aluminum alloy is also easily welded and joined. However, in its –T6 condition the welds may lose some strength, which can be
Material properties of the AW 6005A-T6 aluminium
Context 1 a comprehensive material a study, the AW 6005A-T6 aluminium alloy was chosen for extrusions, because of its excellent mechanical and anticorrosive properties - see Siwowski
What is T6 heat treatment for Aluminium? -
T6 temper 6061 has an ultimate tensile strength of at least 42,000 psi (290 MPa) and yield strength of at least 35,000 psi (241 MPa). In thicknesses of 0.250 inch (6.35 mm) or less, it has elongation of 8% or more; in thicker sections, it has elongation of 10%. What is considered aircraft grade
Aluminium–copper alloys -
Aluminium-copper alloys (AlCu) are aluminum alloys that consist largely of aluminum (Al) and traces of copper The AlCu cast alloys are prone to hot cracking and are used in the T4 and T6 hardening states. The following table shows the composition of some grades according to DIN EN 1706. All data in percent by mass, the rest is